BeeProg2C Extremely fast universal USB interfaced programmer

http://www.elnec.com/products/universal-programmers/beeprog2c/

FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Improved pin drivers drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices.The programmer performs device insertion test (wrong or backward position) and contact check (poor contact pin-to-socket) before it programs each device. These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.The selftest capability allow to run diagnostic part of software to thoroughly check the health of the programmer.Built-in protection circuits eliminate damage of programmer and/or programmed device due to environment or operator failure. All the inputs of the BeeProg2C programmer, including the ZIF socket, connection to PC and power supply input, are protected against ESD up to 15kV.BeeProg2C programmer performs programming verification at the marginal level of supply voltage, which, obviously, improves programming yield, and guarantees long data retention.Various programming adapters are available to handle device in PLCC, JLCC, SOIC, SDIP, SOP, PSOP, SSOP, TSOP, TSOPII, TSSOP, QFP, PQFP, TQFP, VQFP, QFN (MLF), SON, BGA, EBGA, FBGA, VFBGA, UBGA, FTBGA, LAP, CSP, SCSP, LQFP, MQFP, HVQFN, QLP, QIP and other packages. USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rateFPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate (useable after upgrade to BeeProg2)on-board intelligence: powerful microprocessor and FPGA based state machinethree D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall timeVCCP range 0..8V/1AVPP1, VPP2 range 0..26V/1Aautocalibrationselftest capabilityprotection against surge and ESD on power supply input, parallel port connectionbanana jack for ESD wrist straps connectionbanana jack for connection to ground

ZIF socket, pindriver

48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 48-pinpindrivers: 48 universalVCCP/VPP1/VPP2 can be connected to each pinperfect ground for each pinFPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pinsanalog pindriver output level selectable from 1.8 V up to 26Vcurrent limitation, overcurrent shutdown, power failure shutdownESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)continuity test: each pin is tested before every programming operation

ISP connector

20-pin male type with missinsertion lock6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (low-voltage including) devices.1x VCCP voltage (range 2V..7V/100mA), can be applied to two pinsprogrammed chip voltage (VCCP) with both source/sink capability and voltage sense1x VPP voltage (range 2V..25V/50mA), can be applied to six pinstarget system supply voltage (range 2V..6V/250mA)ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)two output signals, which indicate state of work result = LED OK and LED Error (active level: min 1.8V)input signal, switch YES! equivalent (active level: max 0.8V)

 

 

转载于:https://www.cnblogs.com/shangdawei/p/3188709.html

相关资源：EEPROM烧录原理