http://www.xess.com/prods/prod048.php XuLA
http://www.xess.com/prods/prod055.php XuLA2
http://www.xess.com/manuals/XuLA-manual.pdf
The programmable logic device on the XuLA Board is either a XILINX 200,000-gate XC3S200A Spartan 3A FPGA in a 100-pin VQFP, or a 50,000-gate XC3S50A.
The XuLA Board uses a Microchip 18F14K50 PIC to perform the following functions:Reset & initialization: Upon power-up or assertion of the reset, the microcontroller initiates the configuration of the FPGA from the Flash and holds the FPGA in its cleared state if the configuration fails. It instantiates its USB endpoints and participates in the USB enumeration process.Clock generation: The microcontroller uses its pulse-width modulation (PWM) circuitry to generate a 12 MHz square-wave that enters one of the FPGA's global clock inputs.USB-to-JTAG communication: The microcontroller accepts configuration bitstreams anddata as packets over the USB link and transforms these into a sequence of transitions upon the FPGA's JTAG pins. It also receives data from the FPGA through the JTAG port which it bundles into packets for return through the USB link.
The XuLA Board incorporates an 8M x 16 SDRAM (Winbond W9812G6JH) that connects tothe FPGA as shown below. To compensate for circuit delays, the clock signal to the SDRAM is re-routed back to a global clock input so the FPGA can synchronize itself with the SDRAM.
Because of the limited number of pins provided by the FPGA's package, the following modifications were made to the SDRAM interface:The chip-select (CS#) is tied low so the SDRAM is always enabled.The clock-enable (CKE) is tied high so the SDRAM always requires a clock signal in order to keep its data refreshed.Both data qualifier mask enables (DQMH and DQML) are tied low to disable byte-wide access to the SDRAM, so all operations involve the entire sixteen-bit data width.A single FPGA pin drives both bank-select inputs (BS0 and BS1). This reduces the accessible region of the SDRAM by half to 4M x 16.
The XuLA Board has a 2-Mbit SPI Flash (Winbond W25X20BV) that connects to the FPGA as shown below.
Due to the limited I/O of the FPGA package, the Flash and SDRAM chips share some of the FPGA pins. In combination with the SDRAM being permanently enabled (its chip-selectis always asserted), this means that the Flash and SDRAM cannot be used simultaneously.Therefore, the following events occur when the XuLA Board comes on:1. The microcontroller puts its FLASH-DISABLE output into a high impedance state and pulses the FPGA's PROG# pin to initiate the configuration from the Flash.2. The FPGA lowers its CSO_B pin to enable the Flash, and then uses its CCLK, MOSI and MISO pins to read the stored bitstream. Because the SDRAM is not active during the FPGA's configuration (SDRAM-CLK is inactive since the FPGA is not configured), it doesn't matter if the SDRAM address and control pins are toggling.3. Once the Flash delivers its bitstream, the FPGA's DONE pin is asserted. The microcontroller senses this and drives its output pin high to de-assert the FLASHDISABLE signal, thus turning the Flash off. The FPGA can't access the Flash any more, but it can access the SDRAM without affecting the Flash.It is possible to set a flag that prevents the microcontroller from disabling the Flash after the FPGA is configured (as described here). Then the logic design loaded into the FPGA can access the Flash, but it can no longer use the SDRAM (the toggling of the SDRAM address and control pins might inadvertently corrupt the Flash contents).
The CHAN* and CHAN-CLK pins connect directly to the pins of the FPGA which typically use an I/O voltage of 3.3V. When driving the inputs of external 5V logic, you should checkthat their VIH threshold is less than the VOH of the XuLA outputs. (This is true for most 5V logic families.)You must also take care not to exceed the input voltage rating of the FPGA pins when they are driven by external 5V logic outputs. A common technique for protecting the Xilinx FPGA pins is shown below. When presented with a voltage greater than 3.3V + 0.7V= 4.0V, the protection diode built into the FPGA pin's circuitry conducts current and the excess voltage is dropped across the 100Ω resistor. This keeps the voltage directly on the FPGA pin from ever exceeding 4V, which is within tolerated limits. The resistor value should be set so the current through the protection diode does not exceed 10 mA.
However, by default, the Xilinx Spartan-3A FPGA disables the protection diodes.In order to enable these diodes, you can place the following text into your Xilinx ISE project constraint file for every I/O pin that will be connected to 5V logic:NET "input_name" IOSTANDARD = PCI66_3;
http://www.xess.com/manuals/XuLA2-manual.pdf
XuLA2 is an open-source FPGA development board, based on Xilinx Spartan-6 LX25 low cost FPGA. The design provides 32MB SDRAM, micro-SD card slot, two voltage regulators, supervisory circuitry based on PIC 18F14K50 microcontroller and USB port for programming the FPGA.
FPGAThe programmable logic device on the XuLA2 is a XILINX XC6SLX25 Spartan 6 FPGA in a 256-ball BGA package (FT256).MicrocontrollerThe XuLA2 uses a Microchip 18F14K50 PIC to perform the following functions:Reset & initialization: Upon power-up or assertion of the reset, the microcontroller initiates the configuration of the FPGA from the SPI Flash and holds the FPGA in its cleared state if the configuration fails. It instantiates its USB endpoints and participates in the USB enumeration process.Clock generation: The microcontroller uses its pulse-width modulation (PWM) circuitry to generate a 12 MHz square-wave that enters one of the FPGA's global clock inputs.USB-to-JTAG communication: The microcontroller accepts configuration bitstreams anddata as packets over the USB link and transforms these into a sequence of transitions upon the FPGA's JTAG pins. It also receives data from the FPGA through the JTAG port which it bundles into packets for return through the USB link.
SDRAMThe XuLA2 incorporates a 16M x 16 SDRAM (Winbond W9825G6JH) that connects to the FPGA as shown below. To compensate for circuit delays, the clock signal to the SDRAM is re-routed back to a global clock input so the FPGA can synchronize itself with the SDRAM.
SPI Flash and microSD CardThe XuLA2 has an 8-Mbit SPI Flash (Winbond W25Q80BV) and a microSD card socket thatconnect to the FPGA as shown below. During FPGA configuration, the bitstream is read from the SPI flash while the microSD card is disabled. After configuration, either the SPI Flash or the microSD card can be accessed by lowering their respective chip-selects and performing SPI read/write operations.
转载于:https://www.cnblogs.com/shangdawei/p/3251829.html
相关资源：数据结构—成绩单生成器